Loader electronic scale position sensor technical indicators Hall type proximity switch Working voltage: DC5~24V . Detection distance: 1~8mm . Operating frequency: 5KHz . Quiescent current: Max. 2mA . Connecting thread: M8×1mm . Operating temperature: -25 °C ~ +70 °C . Protection level: IP67 . Standard detector Permanent magnets. Dimensions: 30 × 10 × 5mm (length × width × thickness). Oil pressure sensor technical indicators Optional oil pressure sensor: S332B type mV signal output type [ China ] Working voltage: DC5V . Range: 0~25MPa . Accuracy: ±0.1% FS . Output sensitivity: 2mV/V . Zero temperature drift: ±0.015% FS/ °C. Safety overload: 120% FS . Connecting thread: M10×1mm . Operating temperature: -40 °C ~ +125 °C . Protection level: IP67 . 8252 current signal output type [ Switzerland ] Working voltage: DC9~32V . Range: 0~250bar . Output signal: 4~20mA . Accuracy: ±0.3% FS . Safety overload: 200% FS . Connecting thread: G1/4" . Operating temperature: -40 °C ~ +125 °C . Medium temperature: -40 °C ~ +125 °C . Protection level: IP67 . Product Certification: CE . 8253 voltage signal output type [ Switzerland ] Working voltage: DC5V . Range: 0~250bar . Output signal: 0.5~4.5V . Accuracy: ±0.1% FS . Safety overload: 200% FS . Connecting thread: G1/4" . Operating temperature: -40 °C ~ +125 °C . Medium temperature: -40 °C ~ +125 °C . Protection level: IP67 . Product Certification: CE . Loader scales technical indicators and installation 3.4 system accuracy Accuracy level: III . Instrument verification accuracy: 0.02% . Single bucket accuracy: 0.5%~1.0% . Accumulated accuracy: 1.0% . Loader electronic scale installation Position sensor installation The position sensor consists of two components: Proximity switch components: main mounting plate (slot with length adjustment), sub-mounting plate (slot with angle adjustment) and proximity switch (probing distance: 1~8mm ). Magnetic block assembly: threaded slide bar, weld nut, fastening nut, nylon block, upper magnet block and lower magnet block. Probing distance adjustment: Method 1: Adjust the distance between the sensing surface of the proximity switch and the magnetic block to 3~5mm . Method 2: Adjust the distance between the proximity sensor sensing surface and the nylon block to 8~10mm . Recommendation: Install the position sensor on the boom base and boom on the same side as the weighing instrument. Oil pressure sensor installation 1 , installation location The oil port interface for loading the upper / lower oil chamber of the motor arm cylinder is the installation position of the oil pressure sensor. Recommendation: Install the oil pressure sensor on the boom cylinder on the same side as the weighing instrument. Loader scales technical indicators and installation 2 , security measures Support the loader bucket with a stable, sturdy base to prevent accidental bruising. The loader must remain off during the disassembly process. Place an oil tank under the oil circuit port to be disassembled. If the loader has been working for a long time, the oil temperature in the boom cylinder may be higher. Before the disassembly, the loader should be kept off for a period of time to prevent burns. Before removing the oil port of the oil chamber, the bucket lifting lever must be placed in the “lift†position to make the oiling chamber communicate with the main tank and release the oil pressure. Before removing the oil passage of the oil chamber, the bucket lifting lever must be placed in the “down†position to allow the oiling chamber to communicate with the main tank and release the oil pressure. When someone is in the loader's cab, it is forbidden to stand under the loader to prevent accidents. 3 , installation A certain amount of sealed raw material tape is wrapped around the thread of the oil pressure sensor, and it is firmly mounted on the plate type tee to ensure that the seal does not leak oil. The extension type screw ( about 24 mm longer than the original screw ) is used to fix the plate type tee (thickness: 24 mm ) and the oil pipe connection to the boom cylinder. Check the oil line interface Start the loader and accelerate the arm lift multiple times. Check for oil leaks at the tubing connection. Please install the oil pressure sensor and position sensor after the welding work is completed to avoid damage. Reasonable wiring Both the oil pressure sensor signal cable and the position sensor signal cable are protected by a hose and secured with a nylon cable tie. When wiring, try to avoid high temperature and easy to squeeze position, and consider the activity requirements of the moving parts of the loader, and reserve enough cable bending length to prevent it from being pulled off. Before the power supply is connected, the weighing instrument power switch must be disconnected and the power cord is not energized to avoid a short circuit fault. Find the DC24V terminal block with relatively stable voltage from the cab , connect the “ +24V †end of the weighing instrument to its fuse, and connect the “ GND †end to the cab metal frame. Before powering up, please make sure that the input power voltage is correct. -------------------------------------------------- -------------------------------------------------- -------------------------------------------------
Organic mung bean protein powder is produced from mung beans. It is an isolated protein. Organic mung bean protein powder has excellent nutrition and health functions.
The Mung bean is a plant in the legume family. Mung beans are mainly grown in India, China, and Southeast Asia. The Chinese have grown mung beans for nearly 2,000 years. They are ubiquitous in China, and there are many types and numbers. Mung beans are also grown in other countries/regions in South Asia, North America, Brazil, and Europe. The main provinces for mung bean cultivation in China are Anhui, Henan, Hebei, Hubei, Liaoning, Shanxi, Shaanxi, and Sichuan.
Mung bean protein isolate is rich in lysine, and sulfur-containing amino acids are the first limiting amino acid. Mung bean protein extracts the main nutrient protein, nutrients, and minerals in mung bean. Modern scientific research has found that mung bean protein is rich in 18 kinds of amino acids, multiple vitamins, calcium, iron, potassium, phospholipids, trypsin inhibitors, and other nutrients. It can effectively promote calcium absorption, repair muscles, and control blood sugar. It has the effects of lowering blood pressure, lowering blood sugar, and lowering sugar content.
Mung bean protein is very close to the protein required by the human body. It is the nutritional essence of mung bean, which is a typical food that combines food and medicine. Mung bean protein has certain water retention, oil absorption, and foaming properties.
The quality and functional characteristics of mung bean protein powder determine its wide application in nutrition, health products, functional foods, flavored foods, and functional beverages. Our organic mung bean protein powder meets EU and NOP organic standards.
Mung Bean Protein,Organic Mung Bean Protein Powder,Organic Mung Beans,Mung Bean Protein Isolate Organicway (xi'an) Food Ingredients Inc. , https://www.organicwayince.com